Wallpaper is posted at the moment, absolutely more with half the effort

There are many real estate renovation procedures and many details. It is understood that wallpaper construction may be the last process of hard decoration of the home decoration, the start of soft decoration. Wallpapers ought to be completed in all hardware such as woodworking, paint, drinking water and electric power, plastering, and after a sanitary washing.

Ground and skirting are installed
❖ Avoid smashing the keel, sawing timber, etc. when laying the ground to make the wallpaper dirty.
❖ Avoid vibration when setting up the baseboard, which causes the wallpaper to split up from the wall surface area, resulting in bubbling and curling of the wallpaper.
❖ Avoid a lot of dirt pollution and bruises when cutting the baseboard.
❖General putty will never be approved at the bottom of the wall, the 1st wallpaper can not be cut neatly, very long time is susceptible to curling, leading to the wallpaper to roll-up.
❖ Avoid kicking the skirting line by sealing the wallpaper with glass glue, so that the drinking water molecules in the wall structure can’t be discharged, leading to mildew of the baseboard.
Following the kicking line is installed, it is possible that the wall and the skirting line are not flat plenty of or have a gap. The post-installed wallpaper has the effect of covering the gap.

Door cover and door are installed
First install the door in order to avoid the wallpaper from being damaged and filthy, in fact it is also simple to repair the paint. If the wallpaper is definitely patched and the paint is repaired (the gap between your door cover and the wall structure and the gap between the skirting lines) will stain the wallpaper.
How big is the card can vary greatly. If the size is too little, the wallpaper will become attached initial, and a blank will appear after the door is set up. If it is full, it will very easily draw the wallpaper when the door is installed, causing harm to the wallpaper.

Wood lacquer finish can’t be wallpapered first, then timber lacquer
❖Because the wood lacquer is sprayed during building, the paint will adhere to the wallpaper. So when the paint is applied, the completed product should be guarded. In particular, the encompassing wall of the cabinet, door, partition, etc. should be covered with a protective film. If it is atomized to the wall structure surface, the structure quality of the wallpaper is not guaranteed, and it is easy to cause problems.

Air-con hole is well
❖ Avoid punching and harm the wallpaper.
❖ Avoid wall vibration when punching, causing the wallpaper to fall off.
❖ Avoid dusting the wallpaper when punching.
Curtain rod hole is pre-made
The positioning of the curtain hanging rod support is well designed, and the hole is made to avoid the hole punching the top of wallpaper. Especially for flocking, silk, deep embossing, special materials and various other hard-to-care wallpapers, make certain to pre-pull the curtain rod holes before Pure paper Wall covering pasting.

How exactly to paste wallpaper?
Take away the wall skin: take away the original color and various other objects on the wall, make use of gypsum powder to fill up the cracked part of the wall structure, and place a bandage after flattening; if it’s sand gray wall, partition wall, it must be covered with glass cloth Or indeed good cloth; some low quality partitions or exterior walls to reach the insulation effect, have to be filled with plasterboard

Slice the wallpaper: first measure the height of the wall structure, then cut the amount of the wallpaper, generally there are two types of cases: no flower wallpaper according to the elevation of the wall is cut about 5 to 8 cm size, as the upper and lower trimming: the flower wallpaper must consider the design symmetry Sex, so the amount of the cut ought to be increased based on the actual situation, usually 8 to 10 cm longer.

Applying glue: Apply the wallpaper glue to the back of the cut wallpaper with a brush, spend special attention to the surrounding edges to become coated with glue to guarantee the building quality, the painted wallpaper, and the glue to handle the fold. 5- 10 minutes (note that no external push should be applied to prevent creases in the wallpaper, especially the cloth). Following the glue is completely penetrated in to the paper, it can be posted, and several wallpapers are applied every time and posted to be able. Special material wallpaper should be glued on the wall, such as velvet sound-absorbing wallpaper, gold foil tin wallpaper, etc.

Wallpaper construction: Generally, the first wallpaper is posted from the top to underneath of the entranceway or the part of the corner. Utilize the squeegee from top to bottom, from the within to the outside, gently scrape the wallpaper, squeeze out the bubbles and excess glue to make the wallpaper flat. Near to the wall.

Wallpaper construction: Generally, the initial wallpaper is posted from the top to the bottom of the door or the corner of the corner. Use the squeegee from top to bottom, from the inside to the outside, lightly scrape the wallpaper, squeeze out the bubbles and excess glue to make the wallpaper flat. Near to the wall.

Before wallpapering, turn off the energy: When wallpapering, should you have a power switch or socket on the wall, you can change off the main power supply, then cover the wallpaper with all the current power and socket, and cut two pairs from the center of gravity. The part collection will show four small triangles, and then use the utility knife to remove the extra wallpaper around.

Trimming and cleaning: Take off the excess wallpaper at the higher and decrease ends. The advantage of the knife ought to be sharp to avoid burrs. When trimming some wall coverings, it is advisable to make use of a Japanese imported blade with a cost of 1 1.5 yuan. Then use a sponge dampened with drinking water to totally wipe the glue remaining on the top of wallpaper to prevent the wallpaper from turning yellowish. If the wallpaper is certainly dry following the wallpaper is dried out, use a knife to slice the injected glue and flatten it to eliminate it. it is good)