Variator

When we put wallpapers, we constantly encounter problems like this. In particular, most of the friends who would like to do their very own wallpapers are more than they need, and lastly they will find that there are always some little flaws.
In fact, as long as the construction is looked after, these problems can be avoided. Today, we will pick out these problems and concentrate on solving them!
Base film peeling
1) Before brushing the bottom film, check if the wall is standard, no powder, no floating layer.
2) Is there a slight crack in the wall?
3) Whether the construction temperature is over 5 degrees.
4) Brush the bottom film too heavy when it is initial, and brush the second one when it’s not dry. Due to the difference in drying time between the inner and outer layers, it may cause peeling.
5) Whether the foundation film is too thick, can be relieved by adding drinking water. After polishing with sandpaper, re-brush the base film.
The treatment of the base film has a great influence on the wallpaper effect, and the most direct effect is the stability of the wallpaper. Therefore, the base film must be handled relative to the requirements of the instructions, combined with actual situation.
Glue overflow
Glue overflow is a common phenomenon along the way of wallpapering. During the construction process, stay away from the glue overflowing the wallpaper surface area through the paper tape. The rubber surface wallpaper is relatively simple to clean. You can use all of the wallpaper except the rubber tape wallpaper. Paper tape structure is recommended.
1) Wipe with a damp sponge for a surface washable wallpaper.
2) Use a dry towel to remove it, suitable for wallpapers that cannot be stained on the top.
3) Absorbed with a wet sponge, suitable for wallpapers with contaminants on the surface.
There are signs at the joint seam
The handling of wallpaper seams is definitely an integral part of wallpaper construction, and several professional construction masters have their own tips. For the layman, pay special attention to the construction. When the wallpaper was used, the glue didn’t completely hurry out and piled up at the seams. The glue reacted with the wallpaper for a long time.
Remedy: 60-80 degrees boiling water a little bottle, plus a bottle of white colored vinegar, wait for the drinking water to cool off, squat at the seam. (Recommended for partial screening), the wallpaper will last better in 1-2 months, and 80% of the traces could be removed.
Wallpaper shrinking
The phenomenon of wallpaper shrinkage is mainly caused by the workers’ lack of strict seams during construction, that leads to this problem in the later stage, which is related to the construction technology of the workers. Since the wallpaper is made from wood pulp, it has the characteristics of hardwood swelling and shrinking, the performance isn’t particularly stable, you will have a certain expansion after the glue is finished, and shrinkage occurs through the drying process. Although the expansion is uncontrollable, employees can control shrinkage during structure.
Most of the wallpaper shrinks are invisible unless the joints aren’t enough. In this case, it is generally preferable to reserve a coincident part at the joint. Generally, it really is preferable that the joint overlaps at 1-3 cm.
If shrinkage has recently occurred, the repair process is relatively simple. Use a wet towel dampened with water to soak the seam for 10 minutes, and use the advantage of the wallpaper knife to pick the wallpaper, that may usually be picked up. If the attachment on the top of wallpaper is a steel surface, it is easy to make the top of wallpaper tarnish and black after scraping, in fact it is not really recommended to operate.
Wallpaper moldy
1) The wallpaper is moldy and generally has spots on the surface of the wallpaper.
(1) The wall ought to be inspected for water seepage.
(2) If the glue is totally dry.
(3)When wallpaper is definitely applied, whether moisture and air flow can be found in the wallpaper for a long period, react with the glue to trigger mold.
(4) The elements is humid.
(5) The wallpaper is wet.
Moldy wallpaper is a problem that people who are wallpapering are worried about. Additionally it is probably the most Modern Style Wall paper difficult complications to resolve after emergence. As a result, this kind of problem should be based on prevention. It is advisable to work in front of moisture and moisture.
Then, after the wallpaper offers such problems, will there be no solution? of training course not.
2) Processing method
(1) The mildew is small. It is suggested to wipe with drinking water or detergent and blow dry with a hair dryer.
(2) Bleaching water is usually easy to irritate the pores and skin and may trigger the wallpaper to fade. It is not recommended.
(3) If the mold is huge, the wallpaper must be replaced. If the wall structure is seepage, it’s important to completely resolve the issue before posting.